Phoenix BIOS Lock Solution

December 19, 2021 By Brian Moses Off

Table of Contents

Recommended: Fortect

1. Download and install Fortect

2. Open the program and click "Scan"

3. Click "Repair" to start the repair process

Download this software and fix your PC in minutes.

You may have encountered an error indicating that the Phoenix BIOS is locked. As it turns out, there are several steps you can take to fix this problem, which we’ll discuss shortly. BIOS security passwords cannot be recovered. If everyone has forgotten any accounts configured in BIOS, resetting CMOS or NVRAM will help reset BIOS to factory defaults and remove passwords from BIOS. ATTENTION: Clearing CMOS or NVRAM using a jumper starts with passwords in BIOS.

Removing the BIOS battery will not set a password on any built-in computers since the early 2000s, since all BIOS settings are stored in flash memory (similar to a USB stick) and not in a backup battery. CMOS memory. The device only provides a real-time alarm, which is likely to be reset on January 1st of the year when mining occurs.

We’ll have to dig in, but chances are there are 2 prominent solder pads on the motherboard, which may be triangular and / or well marked and hopefully visible when you remove the service cover on the bottom of the laptops. You should summarize these changes by pressing the power button, perhaps for the minimum amount of time, or a similar log.

But it can be a little tricky to not only select the correct sequence, but keep the pads short while you press the power button. This, of course, will be much It’s easier if you solder a pair of sail cables from the end to the pads using a push-button switch.

BIOS passwords are used to enhance the security of laptops or computer systems. You can specify details to prevent access to BIOS temperature or prevent PC from booting.

But sometimes this extra security can be annoying if you forget this BIOS password or intentionally change someone’s system BIOS password.

But there is nothing to worry about. There are many known ways to reset, remove / bypass passwords:

Using MS DOS Command
Using a BIOS backdoor password

DISCLAIMER: This information is intended for advanced users. It is not intended for casual hackers, users, or desktop thieves. Do not attempt the following procedures if you are not generally familiar with computer hardware. We are not responsible for the first use or misuse of this information, such as personal injury, loss of personal data and possible damage.Periodic damage. So use the idea at your own risk. All

Recommended: Fortect

Are you tired of your computer running slowly? Is it riddled with viruses and malware? Fear not, my friend, for Fortect is here to save the day! This powerful tool is designed to diagnose and repair all manner of Windows issues, while also boosting performance, optimizing memory, and keeping your PC running like new. So don't wait any longer - download Fortect today!

1. Download and install Fortect

2. Open the program and click "Scan"

3. Click "Repair" to start the repair process

For fast motherboards, a small coin-sized CMOS bank is used to store all BIOS settings with a password. To reset our password, turn off your computer, open it and remove the CMOS car battery for about 15-30 minutes, and this time put it back in. It will reset BIOS settings and definitely the one you need and password to re-enter all settings.

Then, if that doesn’t work, remove the battery for at least an hour.

Almost all motherboards have a jumper that can be used to remove each individual cmos setting as well as the BIOS password. The location of this jumper depends on the organization of the motherboard. You must read the motherboard cable to check the location. When customers don’t have manual jumpers next to CMOS battery. Most manufacturers identify the jumper as CLR, CLEAR, CLEAR CMOS, etc.

These models use the Phoenix BIOS. If you want to access BIOS setup on these systems, the human body must be shut down and not in sleep / suspend or hibernation mode. Press the new power button, then immediately press and hold the very important F2. When POST (Power On Self Test) completes, the computer displays with BIOS setup.

When you find a sweater, take a close look. There are many more pins, and it seems that the jumper connectsleft or right contact with middle contact. All you have to do is remove the jumper and connect the middle flag to the opposite pin. For example, if a jumper connects the center pin to the pin, remove it and connect the center pin to the code on the right. Wait a few seconds, then remove the pin and connect the middle pin to the left pin.

Make sure most computers are turned off before opening the case and installing the jumper.

Using MS-DOS Command:

This method only works regardless of whether you have access to the system at startup, as this recommended method requires MS DOS. Open Command Prompt from the Programs menu and enter the following commands in turn:

NOTE. The first character in the above sense of the English language is the letter “o”, not the number 0.

After giving commands, reboot the system; in this case, the CMOS settings must be cleared using the BIOS password.

If you are wondering how it works? so let me explain the commands before:

BIOS Phoenix now with Main – Advanced – Security at the top of the screen. Your business can adopt this way of thinking. Use the right arrow to navigate to advanced. Arrow under Advanced next to the Reset Configuration Data Plane and change the value from Disabled or No to Enabled or Yes.

In this method, we only use the MS DOS debugging tool. The “o” character, available for execution in commands, sends suggestions to the I / O ports. The numbers 75 and 71 are the port numbers used to access the CMOS callback. By providing an FF value, we usually tell the CMOS that there is a fantastic bad checksum and we reset the CMOS as well as the BIOS settings and password.

Some software may actually reset the CMOS and / or BIOS password, or both, with a few clicks. But, as mentioned, you must have access to the powered on system and therefore access to MS DOS or MS Windows:

CmosPwd
KillCMOS

Using BIOS Backdoor Password:

Press F12 at startup.Log in and set the old password.Go to the Security Settings tab.FromChange the power-on password by entering the current password and leaving the new password field blank.Close the BIOS screen and save the settings.

Some BIOS manufacturers include an entry in the BIOS password that is always in effect, regardless of which password you purchased in the BIOS. Password used for testing and troubleshooting errors and malfunctions.

Biostar – Biostar
Compaq – Compaq
Dell – Dell
Enox – xo11nE
Epox Central
– Freetech – Posterie
I will – I will
Jetway – spooml
Packard Bell – bell9
QDI – QDI
Simens – SKY_FOX
TMC – BIGO
Toshiba – Toshiba
VOBIS and IBM – Merlin

NOTE. All of these passwords are case sensitive and manufacturers change them from time to time.