An Easy Way To Fix Partition Magic Error 10055

January 19, 2022 By Gary Lamb Off

Table of Contents

You may encounter Partition Magic error 10055. There are various ways to solve this problem, and we will talk about them a bit later.

Recommended: Fortect

1. Download and install Fortect

2. Open the program and click "Scan"

3. Click "Repair" to start the repair process

Download this software and fix your PC in minutes.

The Xbox 360 Slim e73 error program occurs when one of your Xbox 360 chips is faulty. As mentioned in solution 1, this is caused by broken solder joints separating the chips on each motherboard. You can solve this problem by heating the chip with a soldering iron or letting the Xbox overheat.

Cold Junction – Ethernet/Southbridge

Details
Major error code:	1 RLOD
Code E/secondary error code:	E73/1021
Binary/hexadecimal:	01001001 / 0x49 -> 73
Known fixes:
1) Southbridge X-clamp fastening 2) Ebb of the southbridge/Ethernet chip area3) Check the area under the southbridge for broken parts and re-solder them. 4) In rare cases, there may be GPU related issues, so the X-clamp fix might work just as well (bigart666)
Related errors: Powered by X-EX.Colspan=”2″>No connection < /th>

Description:
This error is caused by cold soldering on the southbridge or ethernet chip. In neuIn rare cases, this can also be caused by a cold pin when the GPU is on one of the lanes leading to the southbridge chip. And the lack of parts (caps, resistors…) under the southbridge can certainly cause this error.
Links:
BJTech bigart666
Clicks:	289465

Comments On This Important Error Code:

Usually turn off the console.Disconnect all accessories connected tofront or back of the game console, including video cables, network cables, or USB devices.Position the console horizontally.On this right side of the console, fully attach the hard drive blank latch to the back of the specified console.

I’ve had the E73 on a Falcon many times when reviewing a particular board. Every time I leave it
Overheating is accompanied by pressure on a small Ethernet chip on the back left, pointing to
Console, just above the south deck. As with all XBox bugs, this could be due to
Millions, but for me personally it was pressure on the ethernet chip.

Hi everyone, I fixed my beloved E73 with Fix X-Clamp. Cheating is just applying most of the law
Also click on GPU to track errors. In ours, I drilled these holes
I can adjust the entire radiator without surgery. Too much and not enough fear e73 sharp
and overheating. Worked to enjoy the charm.

Definitely not an Ethernet error. It’s just a video glitch ana a or southbridge…

Successfully repaired only the south bridge ZT-7 with the Station – 250С on
show.

I bought a refurbished Falcon Xbox 3 motherboard and opened it right away
looks like the lady who refurbished it has picked up a new trend in some
Current to another resistor/capacitor. on the motherboard it was e73
so remarkable that I guess there was an e73 error. So if you’ve lost the resistor difference, don’t do it.and all the extras, I’ll take the situation to show you what your ex did

In some cases, a faulty AV cable can cause an E73 error.

NOTE: We repair hundreds of consoles. Last time we found E73 1021, we got it
He left to find broken chips for the processor because the consumer **cr** was trying
fix it yourself,

reinstall the game If you encounter error code 0x87e50014 with a particular game, then you will need to uninstall that particular game in order to reinstall it.

Therefore, the card is NOT SUITABLE and you can buy a new Xbox
🙂

So this error is almost always not just a reflow, but means NOT. REMAINING CHIPS

Hello,
There is quite a lot of information here. I had a big error E73 on the box, so I took the mother
Find out who can inspect it and look for some small (micro) connectors up front.free from the base of the largest particular processor (CPU?). I had a magnifying glass
The glass to see the crowd was loose trying to run traffic jams freely but it
so small it’s almost impossible! The board stopped working, what should I do?

@bigart666 Yes, it worked, after overheating. i
corrected x exactly and still error so it doesn’t mean their particular the
Graphic card. Southbridge is an x-clamp-fix that everyone should do.

The center light associated with the power icon on your Xbox 360 console will flash red. A flashing garlito light on the power button indicates that your console is not getting enough ventilation. The red light will flash until the console cools down.

The correct way to distribute HANA GPU CPU is to use the BGA repair station here
uses infrared radiation and covers an area unlike a heat gun. I fixed a ton
Fixing error E73 on consoles with error E74 simply with BGA tweaks
drain the station again and finally fix it with clamp X! Heat gun 24–30 USD instead of one
SolderingBGA station from $800 to $1900!

I reallocated the GPU twice in this round before I realized it was someone who did it
Remove the cover from the top of the processor. waste of time. It will go into the spine
A client who probably posted it on FLeBay in the past and I can count on its origin
first!

Error E73 is also caused by missing capacitors on the CPU. Be sure to check them out
How?” Or “What”. Most workers will not notice that there is a lot missing.

Check that all credentials are correct and correct them if necessary. Select your login name in the top right corner, then select Sign Out. Select Sign In in the top right corner and enter your Microsoft account credentials to sign in. Try reconnecting to Xbox Live.

This is the GPU I’ve been tolerating. One of them just messed up, put three cotton swabs, 1 in each fan, understood
Overheating boom, it worked so I had to leave to restart the GPU

I got a serious e74 error and reflowed my heat gun. now i get error e73 1021
Mistakes. what i can do any ideas? why did I grow e74 and not e73?

I got error E73/1021, I made a homemade build announcement. Hybrid only on the GPU. Found
Component video still won’t show anything, HDMI and VGA will show
Error E73on the screen. Overheated with CPU fan on for 8 minutes (was hot
enough), let it cool for about 60 minutes, try it and it worked! But only displayed
The logo and never got in your way (the image moved anyway) and hence the color and sync
off

The mobo screws are now evenly lightly tightened, tight and green.Glowing in front of the crystal dashboard!

Recommended: Fortect

Are you tired of your computer running slowly? Is it riddled with viruses and malware? Fear not, my friend, for Fortect is here to save the day! This powerful tool is designed to diagnose and repair all manner of Windows issues, while also boosting performance, optimizing memory, and keeping your PC running like new. So don't wait any longer - download Fortect today!

1. Download and install Fortect

2. Open the program and click "Scan"

3. Click "Repair" to start the repair process