Why is my Konica Minolta Bizhub C353 not working?

Since installing a working Konica Minolta bizhub C353 MFP, we now have a problem with the entire network card to improve MFP locking (not responding to pings, online utilities do not come) and a queue of photos that shows the device in a new suspended state.

What causes Konica Minolta C353 trouble code c-1183?

This error code C-1183 refers to the finishing group on the machine. This error is almost certainly a malfunction of the elevator drive or the finisher output hopper elevator drive. Usually, engine failure is not the reason for idea failure. This could be due to an unstable output bin assembly.

What are the error codes for Konica Minolta?

EAP authentication does not work (user ID, password, certificate, etc.) Server credentials verification failed (EAP-TLS / EAP-TTLS / PEAP). Phase 2 System Negotiation Error (PEAP). The response time from the remote computer has timed out.

Easy To Fix Konica Minolta Error C353

October 19, 2021 By John Anthony Off

Table of Contents

Over the past few weeks, some users have reported that they have encountered Konica Minolta error c353.

Recommended: Fortect

1. Download and install Fortect

2. Open the program and click "Scan"

3. Click "Repair" to start the repair process

Download this software and fix your PC in minutes.

Code: C0001
Description: LCT connection failed
Tool:

Code: C0202
Description: Feed above / below Tray 1 is incorrect
• The separate upper limit sensor of the paper feed tray is not blocked byeven after a certain time has passed after the start of most lifting movements.
Remedy: 1 Check that this m8 connector is properly connected and correct if necessary. 2 Check the actual M8 connector for proper reception and correct pairing if necessary. check some PS8 I / O sensors, check. some tax audits M8. 5 Modify M8. 6 Edit the PRCB.

Code: C0204
Description: anomaly lifting / lowering in the feeder compartment 2
• The sensor of the upper end of the plastic paper feed tray 2 is permanently blocked even after a while if the lifting motion is started for a long time.
Remedy: Make sure only one M9 connector is properly connected to Netlink and correct if necessary. 2 Check the M9 plug for a perfect coupling of the drive and correct if necessary. 3 PS15 control, see I / O sensor. 4 Functional test M9. 5 Edit M9. 6 Edit the PRCB.

Code: C0206
Description: Feed errorand up / down in tray 3.
Tool:

Codification: C0208
Description: anomaly lifting / lowering in the feeder compartment 4
Tool:

Codification: C0209
Description: malfunction of the LCT lift motor.
Tool:

This article describes the cause and instructions for resolving error c-1183 in Konica Minolta bizhub C203, C253, bizhub and bizhub C353 copiers.

how to fix Konica Minolta C353 C-1183 malicious code

This articlecontains an informed solution to the laws of error c-1183 in Konica Minolta bizhubCopiers C203, bizhub C253 and bizhub C353. There have always been common solutionsPlease fix this handy error code. Hope your problem can still be resolved.

ValueType Of Error Code C-1183

This problemCode C-1183 refers to the GPS system of the paver finisher. This mistake often happensDefective finisher output tray elevator motor or defective elevator drive motor.Usually the cause of this error is not a motor failure. This is mycan be closedunstable output due to bleach tray block. Hence, he cannot move properly. hereTrays because the elevator sensors in the house are activated. If it’s rightinstalled, it may not work correctly. Therefore, they need to be properly adjusted.If the error code continues to appear, check the following general details. Replace it ifnecessary.

Some reasons may be

Check the output tray motor plus connector.
Check sensor and connector.
Replace PWB-A FN.
Modify the FSCB. I hope

Recommended: Fortect

Are you tired of your computer running slowly? Is it riddled with viruses and malware? Fear not, my friend, for Fortect is here to save the day! This powerful tool is designed to diagnose and repair all manner of Windows issues, while also boosting performance, optimizing memory, and keeping your PC running like new. So don't wait any longer - download Fortect today!

1. Download and install Fortect

2. Open the program and click "Scan"

3. Click "Repair" to start the repair process